A reputation built one customer at a time
Trusted by tens of thousands
4.9 out of 4823 reviews
All product reviews
2018 Ford F-150
The cover is good quality but it was difficult to install but it did have very good instructions. It was damaged when I received it but they had excellent customer service and it was replaced. Overall I am very pleased.
- Customer Support
- Ease of Use
- Strength and Durability
- Ease of Installation
2023 Toyota Tacoma
Great looking bed cover, have gotten a lot of compliments on it. Putting it on the truck initially was a two person job, once on, it hangs a bit on the back slide bar, with pulling of the bed a piece of the rubber gasket material became mashed and pinched up. Since opening and closing the bed cover, and more use the slide bar issue has been resolving, maybe needing to break in, the rubber gasket issue I keep an eye on. In terms of keeping things dry on trips etc, it does the trick, though water and dust does seep in but that is to be expected. All in all, works well, my wife easily uses it as well, and it looks good.
- Customer Support
- Ease of Use
- Strength and Durability
- Ease of Installation
2023 Ford F-150
Installation was relatively easy following the directions. It looks great on. It leaks my only fault for it so far. I am worried about hell damage or anything that hits it as it is metal and it’s thin.
- Customer Support
- Ease of Use
- Strength and Durability
- Ease of Installation
2024 Ford F-150
The support bar second from the cab came bent, I installed it and was hoping it would straighten out but it didn't. So this causes a leak when washed or rain.
The cover was easy to install with the help of your Videos and Paper instructions. It's a great looking cover with the exception of the bent rail, which is very visible to me.
- Customer Support
- Ease of Use
- Strength and Durability
- Ease of Installation
Jacob R
2022 Ford F-250
Quality seems sturdy so far. I’m not impressed with the large gasket seal that hits the tailgate. It’s was cut like a razor by the side seal the first time I closed the cover. Also the angled roll guide seems flimsy and doubt it will hold up over time. We’ll see
- Customer Support
- Ease of Use
- Strength and Durability
- Ease of Installation
2021 Ford F-250
Have had the cover on for about a month now and I would have to say it’s the best one I’ve had so far. Installation was straightforward and directions were easy to follow, but it still takes some time to get it all together. Had some heavy rains and water does find its way into the bed but nothing crazy. About the norm for every cover I’ve used. Being able to take the panels out is a great feature and very easy to do. Overall fit and finish is solid. Would recommend.
- Customer Support
- Ease of Use
- Strength and Durability
- Ease of Installation
2011 GMC Sierra 1500
Overall satisfied with the bed cover. I feel a couple things could have came pre assembled like the cab side rubber seal. Wish there was a built in way to secure panels when folded up while driving other than having to climb in the bed and tie the cord around them. Ease of use and material is a plus.
- Customer Support
- Ease of Use
- Strength and Durability
- Ease of Installation
2022 Honda Ridgeline
Put it on solo in about three hours, probably 30 minutes of that was second guessing myself on one step. Install videos are very well done and the illustrations in the directions make it a cinch to put together. Have a screwdriver that accepts a socket as well as a ratchet for the job, some of the bolts end up being hard to reach at certain points. The trunk opens about 5-6 inches less with this installed, but still completely usable even with the cover completely closed. No road noise, rattles, anything. Looks great. Makes the bed much more useful.
Deduct one star for shipping. One box in the shipment arrived, then waited another week for the second box to be delivered to the wrong house. Fed Ex performance isn't Peragon's fault, choosing to use them is. If FedEx is reliable at your address order away, if they aren't...be prepared to chase your order down.
- Customer Support
- Ease of Use
- Strength and Durability
- Ease of Installation
2020 Honda Ridgeline
Love the quality of the material and the instructions were pretty easy to follow. My only gripes would be the rubber pieces that protect the ends of the rails not fitting perfectly and at risk of flying away. Maybe having a flush mounted screw that secures the endcaps in place. Also I wish there was a standoff from the truck bed for the component that connects to the locking rods.
- Customer Support
- Ease of Use
- Strength and Durability
- Ease of Installation
2024 Ford F-150
I want to say this cover looks and works amazing NOW. Before I bought the cover I read the reviews, all the F150 reviews and they were for the most part good. I also watched the installation video a couple of times, it didn't look too bad. So I bought the cover. This is going on a 2024 1 week old F150. So I start to read the directions and they seemed ok. BUT when I started to put the brackets on they would not fit because my bed liner is a Ford plastic bed liner not the spray on that is shown in the video. What does that mean... yup get the saw out and start trimming that new liner and try not to scratch that new truck(Good Luck). It wasn't too bad but definitely not what I wanted to do. I did call them to verify and they said yes the liner would have to be trimmed and sent pics of what I already did(very nice lady though). The next step was to put the piece across the back under the window. Guess what it did not fit because the cover was in the way so I called them AGAIN and sure enough they said I had to notch each side of the liner and again they sent me pics and were quick about it and very nice. I asked at that time if I had to cut the whole lip across the back and they said no just notches on the side. WELL you guessed it still didn't fit and low and behold eventually they said I had to cut the lip off all across the bed. Good luck not scratching the new truck, not possible. they wanted me to leave a 1/4" to give the back of the cover some integrity, but for my cover it took the stiffness away and the back would not stay on back of the bed, I had to use Sheetmetal screws to keep it against the back wall. After that I assembled the rails and got the cover on the truck. With all the cutting and calling customer service I had 4 hours into it and it looked terrible, I tried to adjust it and could not get it right, because I couldn't get it to fit right the rear seal on the cover tore so that will need replaced. I ended up taking my truck to the local truck accessory shop and they re-fit and adjusted the cover perfectly. With that said I love the cover LOOKS, EASE OF USE AND EASY TO REMOVE AND REINSTALL THE COVER. I love it!!!! Here is the bottom line. I wish they would show the installment with the drop in bed liner even mention all the cutting and trimming needed. they do mention it on page 4 or 5 of the instructions. I think it needs to be up front on the web page. Also it did cost me $150 to have it re-fit and the truck is a lease so I will have to replace the bedliner when turning the truck in and hopefully not notice the scratches. I still would recommend the cover BUT, consider having a dealer putting it on. I wish I would have thought of that to start. I think they should replace the seal that tore but we will see. Hope this helps!
- Customer Support
- Ease of Use
- Strength and Durability
- Ease of Installation
Jacob R
2020 Ford F-150
Overall I would make this purchase again. I love the concept and versatility of this bed cover. The ability to take it off whenever needed is great, the sleek design makes my truck look so much better. I would not consider this a set back but the installation was a little more difficult than anticipated. At the end of the end it was secured and triple checked to ensure it was installed correctly; however, was still not anticipating putting all that together. Again, that is not a set back just a statement to be made for anyone reading this review before purchase. When closed the bed cover is secure and locks which I love. On the other hand, there is a lot more leaking of water than anticipated as well along the sides. I’m addition I was not anticipating the inability to use the full bed space when opening and closing bed cover. That little bit of space in the back of the bed that needs to be left open to ensure proper opening and closing can be a bit of a pain (no big deal just bought a cargo bar to prevent things from going back that far), especially when you want to use all of your bed space. Every bed cover has its upsides and downsides. I like this cover enough to say it’s worth it and I would purchase again just keep on mine the downfalls.
- Customer Support
- Ease of Use
- Strength and Durability
- Ease of Installation
2012 Ford F-250
The Peragon is exactly as advertised. The following comments are not meant to downgrade my evaluation, but hopefully help others.
1. Installation was not straight forward. It required un-installing, re-installing, multiple nut loosening and re-adjustments. Main issue was where I had installed the ramps vs. sliding the bolt into the rail. The ramp was in the way so had to un-install, remove ramp, slide bolt in rail, install ramp and install system. If your cover doesn't operate smoothly, loosen nuts, raise rails slightly, check front-to-back width, repeat until smooth operation.
2. The cover wouldn't "snap" into the right side of the front cross-member. I had to slightly bend the silver piece to get the system to seat properly. Yes, I was properly seated on the left side with the pin in the hole.
3. Side rail alignment was not straight forward. It took several iterations to get it right, requiring loosening of nuts and re-tightening.
4. The side rails sit mostly inside your bed rails. The cover side rails will reduce your bed opening slightly.
5. The side rails are fairly light weight (which is what we want, right?). If you bump into them too hard, grab onto them when falling, etc., they will bend.
6. Once I got the system to open and close easily, then the lock wouldn't engage. Had to do some fenagling (still not sure what finally fixed it) to get the lock bars to engage. With system installed, I can't see where they are supposed to engage, so that made it more difficult.
7. I've seen a lot of reviews/complaints of leakage. Through a car was, they do leak slightly. I'm sure it will get worse as they get older. I did not expect a hermetic seal so doesn't bother me too much. Maybe the website oversells the "keep stuff dry" aspect.
8. I installed the cover over a 5th wheel hitch. It fit which is one of my main reasons for purchase. You can remove the cover part entirely, but it's not necessary to remove the cover to use the hitch, at least with my hitch/5th wheel combination.
9. The long strap does get irritating, but I knew it was there and was willing to get irritated :). Kind of like marriage! You make your choices..
10. Love the low profile and the appearance of the installed cover. Once adjusted, works easily. I like that it can be closed/locked, opened yet still see out rear window, and can be removed for longer/larger loads in truck bed.
** Vehicle details which may have exacerbated my installation: plastic truck bed rail tops, bed rug, including up the sides of the bed. **
- Customer Support
- Ease of Use
- Strength and Durability
- Ease of Installation
2018 Dodge Ram 1500
I got the Platinum edition cover for my RAM 1500. Cover went on fairly easy, watch the install videos and take your time and it's not a big deal at all. The cover looks good on the truck, I like the hard locking shell for security. I live in the PNW it rains a lot in the winter, the cover does leak a little water here and there but it's no too bad, I think all bed covers leak at least a little no matter which type or brand you get. I was a little surprised how much leaking I got through the rubber seals between the 1st and 2nd panel behind the cab during the snow. As the snow sat on the cover and began to melt in the sun, quite a bit of water leaked into the bed through the seal. Melting snow is not a normal issue in my area so I'm not too worried about it. I'm sure the seals weren't really designed for a couple inches of snow to sit there and melt. There's no where for the water to go and the truck was just sitting, if I was driving it and the water had somewhere to go maybe it wouldn't have been so bad. Other than that I really like the cover so far.
- Customer Support
- Ease of Use
- Strength and Durability
- Ease of Installation
2016 Nissan Titan
I've had one of these tonneau covers for years now, I like it, nice and sturdy. I had it come apart between panels a couple times pushing down to open it, but it was an easy fix, and probably caused by me pushing to close to one side rather than in the middle causing the pin to come out from the hole in the adjacent panel.
The one knock I have against it is it takes up 1/4 to 1/3 if your truck bed for the opening and closing action. Which is not good for when you want to load your truck up for camping or something like that, you can't fill that part of the bed.
- Customer Support
- Ease of Use
- Strength and Durability
- Ease of Installation
2021 Chevrolet Silverado 1500
I love this cover but for the money it should not leak at the collapsable joints. This is really my only issue with it. My only other issue that can be improved by Peragon is that it should have 1/2" fiberboard insulation on the underside of the cover in order to cut down on the heat that gets trapped inside of the truck bad on very hot days such as 90° weather. Other than these things it is a great cover.
- Customer Support
- Ease of Use
- Strength and Durability
- Ease of Installation
2012 Chevrolet Silverado 1500
INSTALLED ONE ON MY 2012 CHEVY SILVERADO WHEN IT WAS NEW ! WASN'T TO BAD TO DO IT BY MYSELF, IT WAS THE STACKING OF WASHERS YOU HAD TO GET RIGHT WITH A LITTLE HELP FROM SUPPORT ! HAD A PROBLEM WITH THE OUTER SEAL COMING OFF WITH THE HEAT HERE ! REPLACED AND ADDED GLUE WITH THE TAPE AND THAT FIXED THE PROBLEM ! THE BEARINGS NEED TO BE OILED UP GOOD AND SPUN EVERY COUPLE YEARS FOR BETTER OPERATION ! THE ONLY PROBLEM I HAVE NOW IS IT LEAKS WATER BETWEEN THE PANELS ! SO THOSE SEALS MIGHT NEED TO BE REPLACED ! IT DON'T RAIN MUCH OTHER THAN THE RAINY SEASON HERE SO MUCH OF THE YEAR ITS USUALLY DRY UNLESS I WASH IT THEN EVERYTHING HAS TO BE OUT ! OTHER THAN THAT 13 YEARS AND I,M SATISFIED WITH IT !
- Customer Support
- Ease of Use
- Strength and Durability
- Ease of Installation
2015 Ford F-150
Generally pleased with the cover, fairly easy to install, looks great. Only complaint, and one that may resolve itself as it is worked in, is that it cannot be opened with one person. I push down after the first panel and it just kind of moves down on the side I am pushing and the passenger side does not also move down so they can be opened. It requires a person each side to begin making them collapse and move forward down the rails.
- Customer Support
- Ease of Use
- Strength and Durability
- Ease of Installation
Jacob R
2023 Ford F-250
Pros-
Looks great
Secure
Reasonably easy install
Cons-
You can’t fill the bed and close it (or open it). This is the biggest one for me. We camp and need to secure a generator and bikes in the bed along with a few tools. The lid sections restrict the use of the last 20% of the bed near the cab making laying the bikes flat in the bed difficult.. This may cause is to get a different cover.
Although installation was ok, we've had to make adjustments several times in one area that seems to come off the rails frequently.
(If this review seems similar to another one it's because we had similar issues and I copied & edited his post because it saved me time.)
- Customer Support
- Ease of Use
- Strength and Durability
- Ease of Installation
Jacob R
2024 GMC Sierra 2500
The bed Cover installed easily and was as described. I love the look of the bed cover and I am happy with my purchase, however, I have two issues that keep me from giving this a five star review. I would like it to be a little more sturdy.....what I mean is that my last cover could hold up to 500lbs and this one will not. My son ,11 years old sat in the center and it bowed it! I was able to straighten it back out, just disappointing. The second is that when you fold the cover up, if there is anything tall in the back of your bed (bucket of baseballs for example) the cover hits it and will not fold up properly without crawling under and pulling it forward. I would still choose this cover because it does pull out easily and it does look good! honestly think any cover with this design would have the same issue and overall it seems to be made well. It seems to keep water out well!
- Customer Support
- Ease of Use
- Strength and Durability
- Ease of Installation
2014 Chevrolet Silverado 1500
Put the cover on with quick clamps and after some fussing with positioning it worked really well. We then took a road trip and hit heavy rain, high cross winds and more. First my MPG went up by 1.7 mpg so that was great and second the storm stood no chance! The cover is solid and kept the luggage and things bone dry. Highly recommend this cover! Oh and the color is one to one. Love it! One down side may be the instructions, they seem to be the same for all versions. Minor complaint after the weather and challenges. I didn’t even mention the lock and soft close, all are great features.
The tie downs are amazing as well. Pulls nice on tighten and these are strong enough to hold a 75ft oak tree upright, though I don’t recommend felling this way :). Real deal awesome and made in the USA.
- Customer Support
- Ease of Use
- Strength and Durability
- Ease of Installation